For cutting lumber, non-ferrous metals, plastics & composites

 

SPECIFICATIONS
Model 208
Model 212
Model 410
Model 410S
Table Height 36" 36" 36" 36"
Table Top 27-1/4" x 31-1/2" 27-1/4" x 31-1/2" 27-1/4" x 31-1/2" 27-1/4" x 31-1/2"
Arbor Motor

5 HP 3600 RPM TEFC

230/460/60/3

7-1/2 HP 3600 RPM TEFC

230/460/60/3

10 HP 3600 RPM TEFC

230/460/60/3

10 HP 3600 RPM TEFC

230/460/60/3

Electrical Magnetic Starter with 110 Volt at Push Button in NEMA 1 Enclosure Magnetic Starter with 110 Volt at Push Button in NEMA 1 Enclosure Magnetic Starter with 110 Volt at Push Button in NEMA 1 Enclosure Magnetic Starter with 110 Volt at Push Button in NEMA 1 Enclosure
Air Equipment 3" x 6" Stroke Cylinder Filter, Regulator & Lubricator, Single Palm Switch-Air Operated 3" x 6" Stroke Cylinder Filter, Regulator & Lubricator, Single Palm Switch-Air Operated 3" x 6" Stroke Cylinder Filter, Regulator & Lubricator, Single Palm Switch-Air Operated 3" x 6" Stroke Cylinder Filter, Regulator & Lubricator, Single Palm Switch-Air Operated
Saw Arbor 1" Stress-proof steel w/4" Saw Collars, 3600 RPM, Timken Bearings, Vee Belt Drive 1" Stress-proof steel w/4" Saw Collars, 3600 RPM, Timken Bearings, Vee Belt Drive 1" Stress-proof steel w/4" Saw Collars, 2900 RPM, Timken Bearings, Vee Belt Drive 1" Stress-proof steel w/4" Saw Collars, 2900 RPM, Timken Bearings, Vee Belt Drive
Saw Blade 14" Diameter, 1" Bore 16" Diameter, 1" Bore 18" Diameter, 1" Bore 18" Diameter, 1" Bore
Cut Capacity 2" Thick x 8" Wide 2" Thick x 8" Wide

4" Thick x 10" Wide, Fence Forward

2" Thick x 14" Wide, Fence Rearward

4" Thick x 10" Wide, Fence Forward

2" Thick x 14" Wide, Fence Rearward

Operating Speed 20-100 CPM-Adj. via Flow Controls 20-100 CPM-Adj. via Flow Controls 20-60 CPM-Adj. via Flow Controls

24 CPM at max blade elevation

40 CPM at blade elevation to cut a 1" x 4"

Adj. via flow controls

Sawdust Outlet 3" Diameter, Rear Exit, 350 CFM 3" Diameter, Rear Exit, 350 CFM 3" Diameter, Rear Exit, 350 CFM 3" Diameter, Rear Exit, 350 CFM
Shipping Weight 750 lbs. (950 lbs. export, 50 cu. ft.) 38" x 40" x 56" H 850 lbs. (1050 lbs. export, 50 cu. ft.) 38" x 40" x 56" H 900 lbs. (1100 lbs. export, 53 cu. ft.) 38" x 40" x 60" H 900 lbs. (1100 lbs. export, 53 cu. ft.) 38" x 40" x 60" H
 
 
Extras for Models 208, 212 and 410
  • Two palm control-anti tie down
  • NEMA 12 Electrics with fusible disconnect
  • In feed roller table 10' long
  • Out feed graduated stop bar with four stops 8' long
  • Additional stops
  • Air over oil feed for non ferrous cutting
  • Lennox lube coolant system for blade, pump type, two nozzles
  • Blades
  • Special Voltages & Hz
  • Custom Roller Conveyors


For More Information, please contact:

Eide Machinery Sales, Inc.
PO Box 11397 / 3219 N. 2nd St.
Minneapolis, MN 55411

TOLL FREE: (800) 344-3433 (EIDE)
Phone: (612) 521-9193 / Fax: (612) 521-9307 
Email: New Machine Sales & Inquiry

 

 
 
For Model 410S
  • Two palm control-anti tie down
  • NEMA 12 Electrics with fusible disconnect
  • Pressure switch on upper guard cylinder - replaces mechanical switch
  • Air over oil feed for non ferrous cutting
  • Lennox lube coolant system for blade, pump type, two nozzles
  • Filled in table center
  • In feed & out feed roller tables 10ft. sections with one leg
  • Out feed graduated stop bar with four stops 10' long
  • Additional stops
  • Out feed drop-off table 10 ft. with 1" graduated stop bar & 4 stops
  • 2" high plain fences
  • 4" high plain fences
  • Steel decks on Tables
  • 10 degree tilt base for for up cut saw
  • 10 degree tilt brackets for tables
  • Mount ledges for TigerStops™
  • Blades
  • Special Voltages & Hz
  • Custom Roller Conveyors